
There are four common ways to cover a garage floor, and each has its place. Here is how each one goes down and what its makers say about it, side by side with how our coated floors are built.
A coating becomes part of the floor. Tiles and mats sit on top of it. A paint kit is a coating you put down yourself. The table sums up how each goes down, using our own system for the coating column and each maker's own instructions for the other three.
| Our coating | Interlocking tiles | Roll-out mat | Paint or DIY kit | |
|---|---|---|---|---|
| How it goes down | Diamond-ground slab, base coat, flake broadcast to refusal, clear topcoat | Tiles snap together on top of the existing floor; no adhesive or special tools | Solid vinyl sheet unrolled from the entrance and trimmed to fit | Degrease, etch with a mild citric-acid solution, roll on |
| The concrete underneath | Cracks, pits and spalls filled and ground flush first | Laid over the existing floor, cracked concrete included, with little or no prep | Floor swept and cleaned first | Loose, chipping or dusty concrete must be removed and repaired first |
| Bonded to the slab? | Yes | No, it sits on top | No, it floats or is taped or glued at the edges | Yes, to the etched surface |
| Before you use it | Things back after 48 hours, park after three days | Per the maker | The maker says to let it relax up to 72 hours in cooler weather | Light foot traffic in 12 to 16 hours, vehicles after 3 days |
| Moving house | Stays with the floor | Can be taken apart and moved | Per the maker | Stays with the floor |
The whole slab is diamond-ground on our Husqvarna and Lavina grinders, edges included, so the coating bonds to open concrete instead of dust and old sealer. Cracks, pits and spalls are filled and ground flush. On about nine floors in ten the base coat is polyaspartic; a rough slab gets a polyurea base and a badly damaged one an epoxy base, under the same clear polyaspartic topcoat. Torginol flake is broadcast to refusal in between, and an anti-slip additive is available. Most garages take one or two days, your things go back on the floor after 48 hours, you can park after three days, and the floor is backed by a 10-year warranty. Garage floors run about $5 to $6 per square foot; repairs depend on the slab, so we look first. More in the cost guide and epoxy vs. polyaspartic.
Interlocking garage tiles are rigid plastic tiles that snap together. A tile maker's FAQ says they need no adhesives or special tools, can be laid right on top of an existing garage floor with little to no prep, and are sold as a way to cover cracked concrete. Perforated tiles let water and other liquids flow through to channels underneath that can be washed out, and the whole floor can be taken apart and moved. The concrete under them stays as it is.
A roll-out garage mat is a sheet of solid vinyl. A mat maker's installation guide says to sweep and clean the floor, unroll the mat from the entrance, let it relax for up to 72 hours in cooler temperatures, and trim it to fit. It can float with a gap at the walls, or be held with double-sided tape, seaming tape or adhesive, and seams are joined with seam tape. The maker describes it as a do-it-yourself install that takes minutes; the concrete under it stays as it is.
A box-store garage floor kit is a coating you roll on yourself, and its instructions spell out the prep: scrub oil spots with a degreaser, etch the floor with a mild citric-acid solution, and do not paint over sealed concrete, poorly bonded old paint, or concrete that is loose, chipping or dusty until it is removed and repaired. New concrete needs 28 days first. The instructions call for air between 60 and 85°F, with the day before at least 60°F, and list light foot traffic after 12 to 16 hours and vehicle traffic after 3 days. The main difference from our floors is the prep: we diamond-grind the slab instead of etching it. If a kit you put down is already lifting, why coatings peel explains what happened, and the old coating can be ground off before a new floor goes down.
If a coated floor is the one, send a few photos or call (531) 239-7575. If your slab is pitted or salt-damaged, start with salt damage repair.
Sources for the tile, mat and kit facts on this page, read November 12, 2026: a tile maker's FAQ (Swisstrax), a mat maker's installation guide (G-Floor) and a garage floor kit's instruction sheet (Rust-Oleum EpoxyShield). No price is given for tiles, mats or kits; ask their sellers.
Papillion crew, Nebraska-registered. Free quotes across the Omaha metro. Nebraska Contractor Registration #76807-26.
They do different jobs. A coating is bonded to the ground concrete and becomes the floor; tiles snap together on top of the slab and can be taken apart and moved. If you want the concrete repaired under a seamless finish, that is a coating.
A roll-out mat is unrolled over the slab, left to relax and trimmed to fit; its maker says it installs in minutes. A coating takes one or two days, goes down over a ground and repaired slab, and stays bonded to it.
Kits are made for it, and their instructions spell out the prep: degrease, etch, no painting over sealed, loose or chipping concrete, and air between 60 and 85 degrees. We grind the slab instead of etching it and put down a polyaspartic system with a 10-year warranty.
It is bonded to the slab, seamless and wipes clean, and cracks, pits and spalls are repaired underneath. It takes one or two days, you wait three days to park on it, and it stays with the house when you move.
Garage floors run about $5 to $6 per square foot for the coating system. Repairs depend on the slab, so we look at the floor and walk you through the number before we start.
Call, text a couple of photos, or fill out the two-minute quote form. We reply fast and the quote is free.
(531) 239-7575Call or text. Serving Papillion, Omaha and the whole metro.